LED Bar

BJ-EI02

Open all sections
Print user manual
  • It’s highly recommended to read this manual before start using the device.
  • The product should be always used under adult supervision.
  • DO NOT cover the ventilation slots.
  • To avoid sight damage, do not look directly at light source.
  • This product is designed for indoor use only.
  • People prone to epileptic seizures should consider the effects of these lights can have on them.
  • Be careful with the cables of the product. If you detect any defect in cable, disconnect the power supply immediately and contact our technical support department.
  • This product is designed to create a visual and sensitive effect; it should never be shaken, tipped or hit with hard objects.

Measurements

  • 1025×65×85mm
  • 1.7Kg

Electrical specifications

  • Power supply: 230Vac 50Hz 
  • Power: 50W
  • DMX cable length: 6m

Introduction

The strip lights create colorful environments that allow you to change the color of the entire room. You can enhance the impact of the projections and the colors of the environments.

A strip light is recommended every two meters for color immersion.

Make the lights change with the music or with your own voice. Compatible with the sensory SHX System.

Product components:

  1. LEDs Bar
  2. Garras de sujeción (x2)
  3. 230V cable
  4. 6m DMX cable
 

  1.          2.           3.          4. 

  • A 230V socket must be available for the power supply of the device.
  • A DMX connection must be available for lighting control (female DMX connector).
  • In case of needing to control more lighting elements, a second DMX connection must be available to ensure the continuity of the signal (male DMX connector).

Necessary elements  for assembly:

For the assembly of the device you will need the following items not included with the product:

  • 4x fixing wall (6mm). Make sure that the plugs are suitable for the mounting surface.
  • 4x screw with cylindrical head

Assembly:

  • The placement of this device must be on the wall or ceiling taking into account that it already has two L-shaped plates to be fixed to the wall by screws and to the bar by palometa.

                                                  

      

  • If more than one bar is available, they should be evenly distributed by placing a separate strip of light every 2 meters to achieve the maximum light bath effect.
  • Plug the LED Bar

      

DMX bus installation

  • Make the DMX connections: for use with the SHX system, the DMX cable must be connected to the DMX IN connector. This cable must be connected to the rest of the DMX bus of the installation. In the event that this element is the last of the entire installation, the bus terminator should be connected to the DMX OUT (this terminator is supplied in the SHX Central Device). If you must continue the DMX signal to another device, you must connect the DMX cable to the DMX out connector.



Equipment configuration:

The bars are configured for use with the SHX system. In case it does not respond to the system it would be necessary to review the configuration which should correspond to the following:

For the model: Beamz LCB 252

Addr – 001

Chnd – 3CH

Slav – SL2

See the manual of the bar to see how to make these adjustments.

Before start using the device
Check the following points:

  • The device must be connected to a wall plug.
  • The DMX cable must be connected to the device.
  • The SHX Central device must be switched on.

Use of the product

  • In the SHX software you can control the lights of the device.
  • In the SHX app, you will also find a tab that allows you to change the colors of the device: you can choose between different colors or activate the function of automatic color changes.

  • In the SHX application there’s a power off button, you can turn off the device with it.
  • You can configure the different contents of the SHX application as well, to create the effects you want to associate with that content. See the manual of the SHX application to learn how to create these contents, (automatic mode, according to the SHX scenes, by sound, simultaneous with the other elements or independent)

The control of this device has been added to the SHX application.
The configuration parameters for this device are:

Lighting control:

  • DMX address: 001

In the SHX application it has been created within the DMX devices with the following configuration:

  • Disconnect the device from the electrical power before cleaning.
  • Use a soft cloth moistened in soapy water to clean the product.
  • Do not use abrasive products.
  • Dry the product before connecting it to the current.
  • Do not connect the device if liquid has entered inside.
  • Don’t cover the ventilation of the lightsource, and keep them clean to avoid overheating.

For a basic troubleshooting of DMX devices follow the next steps:

When a DMX device is affecting the well functioning of other devices on the DMX bus, follow the next steps to identify wheater if a device is faulty or the issue is related to the cable used to connect all the devices.

  •  

  • To avoid possible damage to the environment or human health that represents the uncontrolled disposal of waste, separate these products from other types of waste and recycle them correctly. In this way, the sustainable reuse of material resources is promoted

  • Private users can contact the establishment where they purchased the product or with the relevant local authorities to find out how and where they can take it to be subjected to environmentally friendly and safe recycling.

Within the legal warranty period we agree to rectify for free by repairing or replacing defects in the product derived from defective materials or manufacturing defects.

Any unauthorised alteration or modifications to the product will void this warranty.

This product complies with EU 2004/108/EC Directive requirements .

Declaration of conformity can be downloaded by clicking on the following link: bjliveat.com

If you find any damage or any material is missing please contact our technical service for assistance.

Qinera

c/ Pacífic 51
08027 Barcelona, Spain
Phone: +34 93 285 04 37
Fax: +34 93 553 56 34
e-Mail: info@qinera.com
web: http://www.qinera.com

Any damage or breakage caused during transport must be notified within three days of receipt.