To ensure the safe operation of the device it is recommended to read this user manual completely before starting to use the device.

  • Power Supply: 115~ / 60Hz
  • Maximum power: supply 130V~
  • RF working frequency: 433 MHz
  • Dimensions: 105x59x50 mm
  • 2 x switch 3.5 mm mono jack plug
    Maximum load:
    • Resistive loads: 2000W/9A (cosφ=1)
    • Motor loads: 1000W/5,5A (cosφ=0,8)
    • Halogen lamps with transformer: 300W/1,7A (cosφ=0,76)
  • Maximum switch output charge: 24V – 1A

BJ Enabler Socket + is a plug and play device that allows activating and deactivating household appliances (lights, heaters, fans, kitchen appliances, stereos, etc.) and switch adapted devices, like communication devices, switch adapted cameras, toys and other devices with a switch input.

Fig. 1. BJ Enabler Socket +.

Fig. 1. BJ Enabler Socket +.


You can activate the Enabler by pressing a switch or by means of any controller of the BJ System.

A) Using BJ System remote controllers

To control the BJ Enabler socket + via any controller of the BJ System, follow these steps:

  1. Select a position on the Enabler’s “RF code selector” (Figure 1). The code assigned to the Enabler is given by Table 1.
  2. Connect the Enabler to the mains, taking into account the device’s technical characteristics.
  3. Program on the remote control the RF code assigned in step 1 (check the remote’s User Guide to carry out this operation).
  4. Connect the device that you want to control to the Enabler’s “socket” (Figure 1) or if you are using a switch adapted device, connect it to the “switch output” with the included cable. Take into account the equipment’s technical characteristics and make sure that the device is turned on.
  5. Press the programmed key on the remote control to activate the device. Every time you press the switch, the socket will be turned on for a fixed amount of time by the time selector according to Table 2.

When connecting switch adapted devices, the switch output will work at the same time and in the same way as the connected device.

IMPORTANT: Whenever the position of the “RF code selector” is modified to assign a different code to the Enabler, it must be unplug from the mains socket for at least 5 seconds. The new code will be recorded when the Enabler is plug again.

Table 1.

  • Activating various Enablers at the same time: It is possible to activate various Enablers located in different places at the same time by adjusting the “RF code selector” to the same position in all Enablers.
  • Activating different Enablers: It is possible to activate different Enablers by pressing a different button on the BJ System controller. You just need to adjust a different position on the “RF code selector” in each Enabler.

B) Using a switch

When you need to control the Enabler locally, you can do so using a switch.

In this case, you can control the Enabler by connecting any switch to the Enabler’s “Switch input” (Figure 1).  Every time you press the switch, the socket will be turned on for a fixed amount of time by the time selector according to Table 2.

The Enabler can be cleaned using a damp soft cloth. Always carry out this operation with the Enabler disconnected.

In the event of a fault in the Enabler, do not handle it and contact your distributor

Waste electrical products should not be disposed of with household waste!

Dispose of the waste product via a collection point for electronic scrap or via your specialist dealer.

Put the packaging material into the recycling bins for cardboard, paper and plastics.

Within the statutory warranty period we undertake to rectify free of charge by repair or replacement any product defects arising from material or production faults.

Any unauthorized tampering with, or modifications to the product will annul this warranty.

This product complies with the essential requirements of the Directives 2004/108/EC and 2006/95/CEE.

The Declaration of Conformity can be downloaded at BJ-214-234-241_conformity.pdf

If, despite of correct handling, faults or malfunctions occur or if the product was damaged, please contact us at the address below:

BJ Adaptaciones
C/ Mare de Déu del Coll, 70, Bajos
08023 Barcelona, Spain
Phone: +34 93 285 04 37
Fax: +34 93 553 56 34