Luminea Lamp

BJ-LLAMP

Info
Open all sections
Print user manual
  • It’s highly recommended to read this manual before start using the device.
  • The product should be always used under adult supervision
  • To avoid sight damage, do not look directly at light source.
  • This product is designed for indoor use only.
  • People prone to epileptic seizures should consider the effects of these lights can have on them.
  • Be careful with the cables of the product. If you detect any defect in cable, disconnect the power supply immediately and contact our technical support department.
  • This product is designed to create a visual and sensitive effect; it should never be shaken, tipped or hit with hard objects.
  • Power supply:
    • 230v (AC) –  24Vdc
    • Power: 70W
    • Dimensions: 110x60x40 mm
  • Controller:
    • RGB Controller, 24V.
    • Dimensions: 125x65x45 mm
  • Lamp:
    • Dimensions: 35 cm in diameter and 140 cm in height.

Length of the DMX cable: 6m

Introduction to the product

 

The Luminea Lamp is a multisensory lighting device designed to create pleasant visual environments, tailored to different objectives such as relaxation, stimulation, or emotional regulation. Through changes in colour and light effects, it allows for the simple and effective transformation of the environment.

Its use helps to structure the environment, reduce sensory overload, and promote states of calm or attention, depending on the configuration. In educational, therapeutic, or residential contexts, the Luminea Lamp facilitates the creation of accessible and personalised environments.

You can control the colour of the LEDs with a 6-button remote, a die, a switch, or through the Luminea App.

You can also use it as part of an environment with the SHX System where it combines with other Luminea devices, and with images, videos, sound, vibration, and other immersive effects.

Components of the SHX LED line

Lamp

Cable DMX (6m)

Power supply

  • A 230V socket must be provided for the power supply of the device.
  • A DMX connection must be provided for lighting control (female DMX connector).
  • In case of need to control more lighting elements, a second DMX connection must be provided to ensure continuity to the signal (male DMX connector).

A. Device Assembly:

DMX bus installation

  • Make the DMX connections: for use with the SHX system, the DMX cable must be connected to the DMX IN connector. This cable must be connected to the rest of the DMX bus of the installation. In the event that this element is the last of the entire installation, the bus terminator should be connected to the DMX OUT (this terminator is supplied in the SHX Central Device). If you must continue the DMX signal to another device, you must connect the DMX cable to the DMX out connector. 

 

Startup

  • Connect the Luminea controller to the power supply.

  • At the moment of connecting it, the LED line lighting will activate in white for 10 seconds. After this time, it will operate in automatic mode (see next section).

Use through switches

This entry turns the device on and off. Once it’s running, the lighting changes automatically.

This entry changes the lighting colour cyclically, passing through the colours red, green, yellow, blue, orange, white, and off. When starting a cycle after being turned off, the bubbles are activated.

Use with wireless remote

You can control the device using the wireless remotes Button 6, Button 1, or from the Luminea mat or die.

Configure these controllers in the appropriate operating mode so that they can control this device (refer to the controller manual) and change the device’s colour directly from the wireless remote.

Control from an Android tablet

If you wish, you can control the lighting directly from an Android tablet with the Luminea app.

The following steps must be followed:

Link the Luminea controller to the tablet.

Select the device from the list of devices in the app.

Use the activities created in the app to control the device’s lighting.

Consult the app’s help to learn how to use it.

 

Use in an SHX room

  • From the SHX software, you can control the device’s lighting.
  • Within the SHX application, you will find a tab that allows you to change the device’s colours: you can choose between different colours or activate the automatic colour change function.

  • By pressing the shutdown button on the SHX application, you can turn off the device.
  • You can configure the different contents of the SHX application to create the effects you want associated with that content. Refer to the SHX application manual to see how to create these contents (automatic mode, according to SHX scenes, by sound, simultaneous with other elements, or independent).

The configuration parameters are as follows:

Lighting control:

  • DMX Address: 001

In the SHX application, it is created within the DMX devices, with the following configuration:

The configuration of the DMX channels must be as shown in the figure:

  • Disconnect the device from the electrical power before cleaning.
  • Use a soft cloth moistened in soapy water to clean the product.
  • Do not use abrasive products.
  • Dry the product before connecting back to the wall socket.
  • Do not connect the device if liquid has entered inside
  • Don’t cover the ventilation of the lightsource, and keep them clean to avoid overheating
  • For a basic troubleshooting of DMX devices follow the next steps:

  • When a DMX device is affecting the well functioning of other devices on the DMX bus, follow the next steps to identify wheater if a device is faulty or the issue is related to the cable used to connect all the devices.

  • To avoid any possible damage to the environment or human health caused by uncontrolled disposal of waste, separate these products from other types of waste and recycle them correctly.

  • Private users can contact the establishment where they purchased the product or with the their local authorities to find out how and where they can safely recycle it.

Within the legal warranty period we agree to rectify for free by repairing or replacing defects in the product derived from defective materials or manufacturing defects.

Any unauthorised alteration or modifications to the product will void this warranty.

This product complies with 2014/30/EU Directive requirements.

Declaration of conformity can be downloaded by clicking on the following link: Qinera.com

If you find any defects or missing materials, please contact our technical service for assistance.

Any damage or breakage occurring during transport must be reported within three days of receipt.

If, despite proper handling, the product does not function correctly, please contact us at the following address:

Qinera
c/ Pacífic 51
08027 Barcelona, Spain
Phone: +34 93 285 04 37
Fax: +34 93 553 56 34
e-Mail: info@qinera.com
web: http://www.qinera.com