• It is necessary to read the entire manual before starting using the device.
  • The product should be always used under adult supervision.
  • Do not look directly at the light, it can damage your sight.
  • Do not plug or unplug the device with wet hands.
  • To avoid fire or electric shocks, do not expose the device to rain or humidity.
  • To clean it, first disconnect it from the power socket.
  • Working voltage: 220 / 240AC 50 / 60Hz
  • Working power: 25W
  • Thread of the bulb: E27.
  • Weight 1.1 kg


Ultraviolet light allows to create special environments where the reflective elements stand out completely, facilitating attention and opening a new world of possibilities.

A powerful ultraviolet bulb lights in a determined area of the room for a long-lasting time.


UV bulb

BJ-234 Enabler Socket+

For the pre-installation of the product you will need:

  • Power socket 230V -50Hz.

Unpack the product carefully.

If you find any damage or lack of material when unpacking, please contact BJLive!. It is recommended to keep the boxes during the period of warranty in case it’s be necessary to return it.

Necessary elements for assembly:

To fix the SHX UV LED light, you will need the following items (not included with the product):

  • 1x screw with cylindrical head (mini diameter 4.5mm)
  • 1x fixing wall.
  • 1x Wide-flanged washer.



The UV light can be mounted on wall or ceiling. It must be installed at a distance of at least 0.5m from the surface to be illuminated.

A separation of 30cm should be left between the ventilation grille and the wall or ceiling.

Do not install the barrel in the following places:

  • Areas exposed to sunlight or sources of heat
  • Wet areas or where the projector can receive splashes
  • Areas with sudden changes in temperature

For mounting, the light has a base with 1 hole. For its installation:

STEP 1. Fix the UV light

  • Use the handle to mark the fixing hole.

  • Make a hole on the wall or ceiling and fix the base.

  • Fix the bulb with the fixing screw. Remember to put the washer between the screw and the bulb holder.

  • Do not cover the ventilation holes of the device.

STEP 2. Connect the power adapter.

Before connecting the feeder, check if the Socket + receiver is properly configured. The position of the wheels of the receiver must be:

  • Plug the power adapter to the Socket +.
  • Connect the Socket + to the wall plug, check if the Socket + receiver is properly configured. 
  • Connect the UV light to the Socket +.
  • Connect the Socket + to a wall plug.
  • It’s possible to connect an external switch to control the UV light externally.




To start up the UV LED spotlight you can do it from the SHX application or through an external switch.

With the configuration delivered from the factory, when activating the UV light, it will change its state.

To activate the UV light from the SHX application, go to the “Control” tab of the SHX application:

As indicated in the previous figure, by clicking on the UV icon it will activate the light when is OFF, and will turn in off if is ON.

IMPORTANT: For the correct operation of the device, the blue wheel of the Socket + device must be in the position 5

To control the fan, there’s a specific configuration for the device created on SHX application.

The control orders of the fan are sent by radiofrequency. The codes associated with the different functions of the fan control are:

  • Code 33: activate / deactivate UV
  • Code 63: disable UV
  • Code 79: activate UV

The configuration parameters of the UV LED light are:

  • Clean the lights regularly to maintain a good functioning condition of the device.
  • Before cleaning disconnect it from the power supply.
  • Clean using soapy water and a soft cloth (well wrung out). Never use chemical or abrasive products for cleaning.
  • Carefully dry the surface and do not feed until after one hour.

The UV LED light doesn’t turn on:

In the event of the UV LED light not starting up, check the following steps:

IMPORTANT:check if the bulb is in AT01 mode (see section “Start-up of this manual)

Some of the LEDs do not light or blink.

There is a problem in the LED panel. You should contact your distributor.

The intensity of the light has decreased considerably.

There is a problem on the LED panel. You should contact your distributor.

Can ultraviolet light be harmful?

The emission of ultraviolet light from this LED light is not harmful, althought it’s recommended to avoid direct eye contact and to kee`a safety distance from the light.

How far should the UV LED light be placed?

The recommended distance to the work at safeway is between 2 and 2.5m.

Which elements can be seen under ultraviolet light?

White elements and fluorescent colors are especially noticeable when working under UV light.

Electrical products should not be disposed of with household waste

  • Dispose of the product at an electronic waste collection point or your specialist distributor. 
  • Place the packaging material in the cardboard, paper and plastic recycling bins.
  • To avoid possible damage to the environment or human health that represents the elimination of this kind of waste, separate these products from other types of waste and reciprocally correct. In this way, the sustainable reuse of material resources will be promoted.
  • Private users can contact the establishment where they purchased the product or the relevant local authorities to find out how and where they can take it to an ecological and safe recycling.
  • Within the term of legal guarantee we undertake to rectify for free by means of repair or replacement the defects of the product derived from defective materials or manufacturing defects.
  • Any unauthorised alteration or modification of the product will void this warranty.

Within the legal warranty period we agree to rectify for free by repairing or replacing defects in the product derived from defective materials or manufacturing defects.

Any unauthorised alteration or modifications to the product will void this warranty.

This product complies with the requirements indicated in the European Directive 2004/108 / EC.

If you find any damage or any material is missing please contact our technical service for assistance.

BJ Adaptaciones
C/ Mare de Déu del Coll, 70, Bajos
08023 Barcelona, España
Fono: +34 93 285 04 37
Fax: +34 93 553 56 34
e-Mail: info@bjliveat.com

Any damage or breakage caused during transport must be notified within three days of receipt.