Vibroacoustic Amplifier

BJ-EMAVIB

Open all sections
Print user manual
  • It’s highly recommended to read first the entire manual before start using this device.
  • The product must be used only
  • under adult supervision
  • The correct use and supervision of this equipment guarantees a long-live performance.
  • Remove the wrapping of the different elements from the vibroacoustic amplifier, save them until you check all the elements work correctly
  • The heat generated by this unit needs good ventilation. Make sure the air vents of the cabinet are not covered at anytime.
  • The device should not be used outdoors or in humid environments.
  • Do not disconnect the device from the wall plug with wet hands.
  • Immediately disconnect the mains plug from the mains socket if:
        1. there is visible damage to the unit or to the mains cable.
        2. a defect might have occurred after a drop or similar accident.
        3. there are malfunctions.
  • The unit must in any case be repaired by skilled personnel.

Rated output power
Stereo………………………………. 4Ω: 2 × 200 W
Stereo ……………………………….8Ω: 2 × 125 W

Peak music
output power (Pmax):………….. 600 W

Input sensitivity for
rated power at 4Ω:………………..1.3 V
Input impedance: …………………55 kΩ
Frequency range: …………………10 –20 000Hz, -0.5 dB
S/N ratio:…………………………… 64 dB
Channel separation: > …………..55 dB, 1 kHz
THD: ………………………………….0.05%, 5 W at 4 W
Power supply: ……………………..230 V/50Hz
Power consumption: …………….max. 730 VA
Ambient temperature: …………..0 –40 °C
Dimensions, Weight: …………….482 × 95 × 300mm, 7.6 kg

Introduction

The vibroacoustic amplifier transforms any furniture into a vibroacoustic element, providing stimuli that allow users to feel the music and sounds like a vibrant and relaxing experience all over the body.

Includes a pre-amplifier stage to which you can connect any music player.

Componentes

  1. Low frequency amplifier

2. Pre-amplifier stage

3. RCA – RCA cable 

4. Jack 3.5 – Jack 3.5 cable

5. Pre-amplifier power suply

  • Two 230V power socket must be available for the amplifier and the pre-amplifier stage.

Connect the different elements following the next diagram:

  • Connect the sound source (MP3 player, PC, etc.) to the pre-amplifier using the jack-jack cable provided (4).
  • To connect the cable, insert it in the jack input and turn the grey disk on the jack slightly to ensure a good connection.
  • Check by pulling lightly on the jack to ensure that it is correctly secured.
  • Connect one end of the RCA-RCA cable (3) to the corresponding amplifier input, and the other end to the pre-amplifier stage, as shown in the following pictures.

  • Connect the power supply cable to the amplifier.
  • Connect the power supply to the pre-amplifier stage.

START UP:

  • Connect the amplifier to the power supply.
  • Connect the preamplifier to the power supply.
  • Turn ON the amplifier.
  • Turn ON the sound source (mp3 or other). Adjust the volume to an appropriate level.

Vibration regulation

The amplifier allows the vibration intensity to be adjusted. The vibration level should be adjusted via the controls on the front, particularly via the CH.A control (or CH.B if there is a second vibroacoustic element).

WARNING!

  • Keep the CH.B control on minimum when only one vibroacoustic element is used.
  • When the vibration level is adjusted, if the “CLIP” indicator is permanently ON (red LED) lower the setting immediately until the indicator turns off
  • Not following these indications can lead to the malfunction of the vibroacoustic amplifier.
  • Before cleaning, disconnect the equipment from the wall plug.
  • Clean using soapy water and a soft cloth (wrung out).
  • Never use chemical or abrasive products for cleaning.
  • Carefully dry the product and do not power it until it’s completely dry.
  • Make sure the ventilation openings are free of dust to ensure proper ventilation of the device.
  • It is recommended a periodic inspection of the devices, in case of detecting any anomaly disconnect the device from the current and immediately contact your supplier for assistance.

In case the shakers do not reproduce any sound, check the following points:

Should any sound come through the vibration device?

This element is designed to produce a vibration from an audio signal, not for audio reproduction. Even so, you may notice a slight sound through the vibration device.

How could speakers be connected to listen to the music?

To connect some speakers you need an audio splitter cable connector.:

For this the main cable should be connected to the sound player and in each of the 2 outputs must be connected the vibo-acoustic amplifier and to the sound system of the speakers.

Electrical products should not be disposed of with household waste.

  • Dispose of the product at an electronic waste collection point or your specialist distributor. 
  • Place the packaging material in the cardboard, paper and plastic recycling bins.
  • To avoid possible damage to the environment or human health that represents the elimination of this kind of waste, separate these products from other types of waste and reciprocally correct. In this way, the sustainable reuse of material resources will be promoted.
  • Private users can contact the establishment where they purchased the product or the relevant local authorities to find out how and where they can take it to an ecological and safe recycling.
  • Within the term of legal guarantee we undertake to rectify for free by means of repair or replacement the defects of the product derived from defective materials or manufacturing defects.
  • Any unauthorised alteration or modification of the product will void this warranty.

Within the legal warranty period we agree to rectify for free by repairing or replacing defects in the product derived from defective materials or manufacturing defects.

Any unauthorised alteration or modifications to the product will void this warranty.

This product complies with EU 2004/108/EC Directive requirements .

Declaration of conformity can be downloaded by clicking on the following link: bjliveat.com

If you find any damage or any material is missing please contact our technical service for assistance.

BJ Adaptaciones
C/ Mare de Déu del Coll, 70, Bajos
08023 Barcelona, España
Fono: +34 93 285 04 37
Fax: +34 93 553 56 34
e-Mail: info@bjliveat.com
www.bjliveat.com

Any damage or breakage caused during transport must be notified within three days of the reception