To ensure the safe operation of the device, it is recommended to read this user manual completely before using it.

Power

 

Vcc= 24Vdc/5A

Connection USB: Type C 5V / 100mA

Salida vibración: Speakon connector

Pmax: 50W

Min impedance: 4ohm

Audio In/Out: Jack 3,5mm stereo connector

 

Radiofrequency

 

Frequency: 433MHz

Range: 30m

Infrared

 

Frequency: 38kHz

Minimum PC requirements for the correct operation of the device

 

Processor: i5 6400 Quad core @ 2.70 GHz

RAM: 8GB DDR4

Video output: DVI-D, HDMI

Integrated wireless connectivity: 1 Dual Band 802.11ac

Main hard drive: 240 Gb

Operating system: Windows 10 pro 64 bits

Before starting:

 
  • Use only the feeder supplied with the equipment to power it.
  • Connect the USB cables directly to the USB ports of the computer. Avoid using intermediate elements to connect them.
  • Make sure that the switches you connect are not associated with any voltage source.
  • Do not install the equipment inside metal cabinets, as they may reduce the coverage of radio frequency signals.
  • When using infrared signal emission to control equipment, ensure that there is direct visibility between the SHX Central Device and the equipment to be controlled.
 

First steps:

 

Power supply

  • Use only the feeder supplied with the equipment.
  • Input voltage: 100V-240Vac 50-60Hz.
    Supply voltage: 24Vdc / 5A
  • Do not use the power supply if you notice that the cables or the connector are in poor condition.

a) Power on:

b) Power off

Connection to PC:

 

a) USB connection:

Connect the device to a computer using the supplied USB cable.

b) Installing SHX software on the PC:

Install on your computer the SHX.exe file found in the USB memory that has been supplied.

Copy the “BJCSHX” content folder that is also found in the USB memory to your computer.

 

IMPORTANT:

 
  • The folder must be saved in C: \
  • The device must be ON and connected to the computer using the USB cable before executing the SHX software.
 

Vibroacoustic elements:

 

The SHX Device vibration amplifier allows the connected elements to vibrate to the rhythm of the music, allowing users to feel the music in the body.

a) Vibroacoustic element connection:

 

IMPORTANT:

 
  • Vibroacoustic element: Min 4 Ω / Max: 50w
  • Do not connect audio speakers.
 

b) Audio signal connection:

** It is necessary to add a Jack – RCA cable

Not included

c) Functioning:

1- Start up the sound player (PC, MP4 …). Adjust the sound volume of the player so that the level is adequate.

2- Adjust the vibration level from the SHX Device using the volume adjustment potentiometer.

Adjust only for vibration.

(The audio output signal is independent of this setting)

 

Lighting device control:

 

The SHX Device Lite allows the control of several (non-independent) lighting elements via DMX. This allows changing the colors and regulating the intensity of the lighting depending on the activity, according to the ambient sound or the projected images.

a) Connections:

The lighting elements are controlled by DMX connections. It is necessary that the lighting elements have this type of connection.

All lighting elements must be connected to each other, using DMX cables (included).

b) Functioning

The elements are controlled from the “Control” tab icons.

Access by wireless controls:

 

This device allows you to receive orders from different elements of the room to wirelessly activate the contents configured in the SHX software. For example: SHX Dice, Button 6, etc.

a) Connections

IMPORTANT:

Mount the antennas and make sure they are not close to sources of interference.

b) Functioning:

From the wireless elements you can activate the software boxes. Each button activates a box on the selected tab.

 

Switch access:

 

The contents of the SHX software can be activated using switches.

a) Connections:

Connect a switch (for ease of use we recommend that it be wireless) to the control inputs according to the desired function.

b) Functioning:

There are 6 direct inputs that activate the first 6 cells of each tab.

 

Inputs for specific functions

Scan: When activating this input, the scanning of the different cells of the active tab begins. A second activation will start the content of the selected cell.

Random: With each activation, a cell of the active tab is started randomly.

Sequential: With each activation of the input, the different cells of the active tab are organized in an orderly manner.

Infrared element control

 

From this device, you can control elements of the environment that already have remote controls, for example: Projector, TV. Using the SHX software you can memorize buttons of other remote controls to activate these elements from the SHX software.

a) Connections:

b) Functioning:

The SHX software allows to memorize the “IR function” of any command, facing the command towards the IR REC identifier.

Consult the SHX manual to integrate this function in a tab or scene.

Activating the programmed box will turn on the device that until now controlled the infrared control.

Enclosed with the SHX Device is an SHX Uer Guide to program the SHX software and customize the room’s operation.

In addition, you can consult the SHX Content Library to download multiple activities and collections.

  • The device must be disconnected from the power outlet before cleaning.
  • Never use chemical or abrasive products for cleaning.
  • Clean the outer surface of the rack on a regular basis to avoid incidents.
  • Dispose of the product through an electronic material collection point or through your specialized distributor.
  • Place the packing material in the cardboard, paper and plastic recycling bins.
  • At the end of its useful life of the product neither this nor its electronic accessories (such as the USB cable) should be disposed together with other household waste.
  • To avoid possible damage to the environment or human health represented by uncontrolled waste disposal, separate these products from other types of waste and recycle them properly. This promotes the sustainable reuse of material resources.
  • Individual users can contact the establishment where they purchased the product or the relevant local authorities to find out how and where they can take it to be subjected to an ecological and safe recycling.Dispose of the product through an electronic material collection point or through your specialized distributor.

The following message appears in the SHX software:

‘Please connect the Central Device and restart the application’

This message appears when the computer does not detect the device. Review the following steps (section 2 of this manual):

  1. Check that the power supply is connected and that the plug has power. The power supply LED must be on.
  2. Check the power connector connection.
  3. Make sure the switch is in I.
  4. Verify that the power LED is blue.
  5. Check the USB connection: securely tighten the USB connectors on both the device and the PC
  6. Close the application and run it again.

The vibration is not noticeable:

  1. Check the connections as indicated in section 4.
  2. Secure the connections according to section 3.
  3. Verify that the connections and the cable of the vibroacoustic element are not damaged.
  4. Ensure that the volume of the input sound (MP3, PC, stereo) is adequate.
  5. Adjust the volume of this device.

The lighting elements do not respond:

To verify operation, it is better to connect a single lighting element directly to this device.

  1. Secure the connections according to section 3
  2. Check the connections according to section 5
  3. Check that the lighting device is on and has the appropriate DMX address.
  4. Review the cell configuration in the SHX software.

If the item that has been tested in the previous sections works correctly, add the other elements of the installation one by one and:

  1. Check if the connections between the different DMX elements is correct.
  2. Check if the DMX configuration of each item is correct.

The SHX Effects radio frequency receivers (BJ-234 Enabler Socket +) do not respond:

  1. Check connections according to section 3.
  2. Check if the antennas are properly connected (section 6).
  3. Make sure there are no elements nearby that may interfere with the signal emission.
  4. Check the radio frequency code setting on the Enabler Socket + receiver and the software match.

The device does not respond to wireless controls:

  1. Check the connections according to section 3.
  2. Check if the antennas are properly connected (section 7)
  3. Make sure there are no elements nearby that may interfere with the reception of the signal. Zoom in on the control element
  4. Check that the control element (control button, given, …) is loaded and turned on.
  5. Restart the application

Switch inputs do not respond:

  1. Check the connections according to section 3.
  2. Check if the antennas are properly connected (section 7)
  3. Make sure there are no elements nearby that may interfere with the reception of the signal. Zoom in on the control element
  4. Check that the control element (control button, given, …) is loaded and turned on.
  5. Restart the application

Infrared controlled elements do not respond:

  1. Check connections according to sections 3 and 9
  2. Repeat the recording process several times in case there has been a recording failure.
  3. Make sure the receiver is on.
  4. Make sure there is direct visibility between the IR emitter and the receiver.
  5. Try to bring the IR emitter closer to the receiver.
  • Within the term of the legal guarantee, we undertake to rectify the product defects derived from defective materials or manufacturing defects free of charge by repair or replacement.
  • Any unauthorized alteration or modifications of the product will void this warranty.

This product meets the requirements of European Directive 2004/108 / EC.

If you find any damage or any material is missing please contact our technical service for assistance.

BJ Adaptaciones
C/ Mare de Déu del Coll, 70, Bajos
08023 Barcelona, España
Fono: +34 93 285 04 37
Fax: +34 93 553 56 34
e-Mail: info@bjliveat.com
www.bjliveat.com

Any damage or breakage caused during transport must be notified within three days of receipt.